By Norman Ford · Updated October 2026 · How we check specs

Commercial truck tire tread depth: legal minimums and chart

Tread depth is one of the simplest things to check on a truck and one of the most common tire violations at roadside inspections. The rules are short, but the details matter: which groove counts, how to measure it, and the difference between a violation and an out-of-service order. This page sets out the federal limits, the inspection levels, how to measure and a checklist you can run at every pre-trip.

Truck tire tread depth chart

Commercial truck tire tread depth limits
PositionFederal minimum (49 CFR 393.75)CVSA out-of-service level (as published)Where measured
Steer (front axle of a truck or truck tractor)4/32 in in a major grooveLess than 2/32 in in two adjacent major groovesAny point on the tire
Drive2/32 in in a major grooveLess than 1/32 in in two adjacent grooves at three spotsSpots at least 8 in apart around the tire
Trailer2/32 in in a major grooveLess than 1/32 in in two adjacent grooves at three spotsSpots at least 8 in apart around the tire
Buses, front wheels4/32 in; no retreaded, recapped or regrooved tiresSee CVSA criteriaAny point on the tire

Source: 49 CFR 393.75, checked October 2026

Cite or embed this

The CVSA figures come from the published North American Standard Out-of-Service Criteria as reported by FleetOwner. CVSA updates the criteria every April, so check the current handbook if you need the exact wording.

Source: FleetOwner, FMCSA, CVSA and tread depth, checked October 2026

Violation vs out of service

These are two different outcomes:

  • Violation. A tire below the 49 CFR 393.75 minimum, such as a steer tire at 3/32 inch, is a violation. It goes on the inspection report and counts against the carrier's safety record, but the truck may be allowed to continue.
  • Out of service. A tire below the CVSA out-of-service level is a hazard. The vehicle cannot move until the tire is replaced.

Neither is a good outcome. A tire at the federal minimum has very little grip left on wet roads, and the violation shows up in your safety data.

What counts as a major groove

A major tread groove is one of the main circumferential grooves that run around the tire. The rule says tread depth is measured in a major groove and not where tie bars, humps or fillets sit. Tie bars are the raised bridges at the bottom of some grooves, and the tread wear indicators are small raised bars set at about 2/32 inch. Measure beside them, not on top of them.

How to measure commercial truck tire tread depth

  1. Use a tread depth gauge that reads in 32nds of an inch. A coin is not accurate enough for a truck tire.
  2. Pick a major groove and push the probe to the bottom, away from tie bars and wear indicators.
  3. Read the gauge and note the depth.
  4. Repeat across the tread in each major groove.
  5. Repeat at several points around the tire, turning the wheel or moving the truck if needed.
  6. Record the lowest reading by tire position.
  7. Compare with the limit for that position.

In spec

Source: 49 CFR 393.75(b): 4/32 in minimum on steer tires. A qualified inspector must confirm; this never replaces an inspection.

Tread depth checklist

Run this at every pre-trip or tire check. Tick each item as you go.

Truck tire tread depth check

0/8 · 0%

What else fails a tire at inspection

Tread depth is only one part of 49 CFR 393.75. A tire also fails if it has:

  • Ply or belt material exposed through the tread or sidewall.
  • A tread or sidewall separation.
  • A flat or an audible leak.
  • A cut that exposes ply or belt material.
  • A load on it greater than its marked load rating.
  • Pressure below what its load requires.

A regrooved tire with a load capacity of 4,920 pounds or more may not go on the front wheels of a truck or truck tractor.

Semi truck tire depth and when to replace

The legal minimum is the floor, not the target. Many fleets set a pull point above it, often to keep enough tread for safe wet braking, to move steer tires to another position or to keep a casing good enough for retreading. Our retread truck tires guide explains why pulling a tire before it is worn too far protects the casing.

To plan when each tire will reach its pull point, use the tread readings from your checklist in the planner on our how long do truck tires last page, or check a single reading with the tire tread depth legal checker.

Tread depth and winter driving

Deeper tread clears water and slush better, and some states and Canadian provinces set their own rules for winter tires and chains in mountain passes. A drive tire that is legal at 3/32 inch may grip poorly on snow. Our winter truck tires guide covers winter treads, and our truck tire chains guide covers chain laws.

Why steer tires have a higher limit

The steer tires decide where the truck goes. If one loses grip or fails, the driver can lose control in a way that a single drive or trailer tire failure rarely causes, because duals have a partner tire to carry the load and keep the wheel end on the road. That is why the federal rule sets 4/32 inch on the front tires of trucks, truck tractors and buses, twice the 2/32 inch required elsewhere, and why buses may not run retreaded, recapped or regrooved tires on the front at all.

Many fleets go further and move steer tires to another position well before 4/32 inch. A tire pulled at a higher depth still has useful tread left for a drive or trailer position, where the legal minimum is lower.

Common tread depth mistakes

  • Measuring on a wear bar or tie bar. These raised areas read shallower than the groove and are excluded by the rule.
  • Measuring only one spot. Tires wear unevenly; the lowest major groove anywhere on the tire is what counts.
  • Skipping inner duals. Inner tires are hard to reach and are where low tread and damage hide.
  • Using a coin. A coin test is rough at best on a truck tire. A gauge costs little and reads in 32nds.
  • Forgetting new tread depth. Knowing what the tire started at tells you how fast it is wearing.
  • Treating legal as safe. A tire right at the minimum has little grip left in rain, slush or snow.

Tread depth on box trucks

The same rule applies to a 26 ft box truck as to a tractor: 4/32 inch on the front tires and 2/32 inch on the rear duals. Box trucks in city work wear steer tires fast, especially on the shoulders, so measure them weekly. Check the inner rear duals too; they are the hardest tires on a box truck to see.

Repairs and tread depth

A tire with enough tread can still need repair. Punctures in the tread area can often be repaired from the inside with a proper patch and plug, within the tire maker's limits. Sidewall damage usually cannot. Our truck tire repair guide covers what can and cannot be fixed.

Tire cost and tread depth

Each 32nd of tread is money. Running tires to the right pull point, keeping wear even and retreading good casings all lower tire cost per mile. The tire cost per mile calculator shows the effect for your prices and miles.

Methodology and updates

The federal limits on this page are from 49 CFR 393.75, checked on the eCFR in October 2026. The out-of-service levels are from the CVSA North American Standard Out-of-Service Criteria as published in trade press, and CVSA revises those criteria each April. We review this page every year after the April update. You are welcome to use the chart and CSV with a credit link to this page.

Dispatch for 26 ft and up

TorqueLoads is a dispatch service for 26 ft box trucks and larger. We find and negotiate loads, the broker sends the rate confirmation to you, and you decide every load. Learn about our dispatch service, read about box truck dispatch, or apply.

Commercial truck tire tread depth FAQs

What is the minimum tread depth for semi truck tires?
Under 49 CFR 393.75, tires on the front axle of a truck or truck tractor need at least 4/32 inch of tread in a major groove. All other tires, including drive and trailer tires, need at least 2/32 inch. The depth is measured in a major tread groove, not on tie bars, humps or fillets, and any one groove below the limit is a violation.
What tread depth puts a truck out of service?
The CVSA out-of-service criteria used at roadside inspections set lower levels than the federal violation limits. As published, a steer tire with less than 2/32 inch in two adjacent major grooves, or another tire with less than 1/32 inch in two adjacent grooves at three spots around the tire, puts the vehicle out of service. The criteria are updated each year.
How do you measure tread depth on a truck tire?
Use a tread depth gauge. Push the probe into a major groove, away from the tread wear indicators and tie bars, and read the depth in 32nds of an inch. Measure several grooves across the tread and at several points around the tire, and record the lowest reading. The lowest major groove is what counts for the legal limit.
How much tread does a new semi truck tire have?
New tread depth varies by tire and position. Steer and trailer tires usually start shallower than drive tires, which often have deep, blocky treads for traction. The tire maker lists the new tread depth on its spec sheet for each model and size. Knowing the starting depth lets you work out how much of the tire you have used.

Apply for dispatch

Legal tread, loaded miles

About 2 minutes. No setup fee. No contract. Every load is your call.

  • 26 ft cargo space minimum, 7 equipment types
  • No setup fee, no contract, no haul no pay
  • The rate confirmation comes to you and you sign it
STEP 1 OF 2 · WHAT DO YOU RUN?

BOX TRUCK · 26 FT MINIMUM

Prefer the full form? Use the long application.