By Norman Ford · Updated October 2026 · How we check specs

SPN FMI codes list: how to read heavy truck fault codes

Key point: the FMI table has only 32 values, 0 to 31, and those meanings are the same on every truck that uses J1939. Learn the FMIs and you can read the type of problem behind any code, even before you look up the SPN.

SPN 157 FMI 18

Example code: fuel rail pressure, data valid but below normal operating range, moderately severe level

Severity: Check soon

Walk it: can I keep driving?

What is the dash lamp?

Is the engine derated or limp mode?

Smoke, loss of braking or steering feel, overheating, or warning sounds?

This helper never overrides your dash warning or your OEM guidance. Likely causes are possibilities, not a diagnosis.

How to read an SPN and FMI code

A fault code on a J1939 truck has three parts you will see on a scan tool or the dash:

  1. SPN, the suspect parameter number. It names the thing being measured or controlled. For example, SPN 157 is fuel rail pressure and SPN 639 is the main J1939 data network.
  2. FMI, the failure mode identifier, from 0 to 31. It says what kind of fault the module found.
  3. Occurrence count, how many times the fault has been logged. A high count on an inactive code points to an intermittent problem.

You will also see which module logged the code, such as the engine, transmission or ABS. Older trucks that use the J1587 standard show codes with MID, PID or SID and FMI instead; the FMI meanings are similar.

FMI table: what each failure mode means

These are the FMI meanings in our own words. FMIs 22 to 30 are reserved and rarely seen.

J1939 failure mode identifiers (FMI) 0 to 31, in our own words
FMIMeaningWhat it usually points to
0Data valid but above normal range, most severeA real reading far too high, such as very high temperature
1Data valid but below normal range, most severeA real reading far too low, such as very low oil pressure
2Data erratic, intermittent or incorrectSignal jumping, loose wiring, a sensor that disagrees with others
3Voltage above normal, or shorted to a high sourceShort to power, open ground, failed sensor
4Voltage below normal, or shorted to a low sourceShort to ground, failed sensor
5Current below normal, or open circuitBroken wire, unplugged connector, open coil
6Current above normal, or grounded circuitShorted coil or wire, failed actuator
7Mechanical system not responding or out of adjustmentStuck valve, actuator not moving as commanded
8Abnormal frequency, pulse width or periodSpeed sensor or PWM signal problem
9Abnormal update rateA message on the network arriving late or not at all
10Abnormal rate of changeA value changing faster than is possible
11Root cause not knownFault found but the type cannot be identified
12Bad intelligent device or componentA module or smart sensor reporting itself faulty
13Out of calibrationCalibration or setup needed
14Special instructionsSee the maker's documents for this code
15Data valid but above normal range, least severeSlightly high
16Data valid but above normal range, moderately severeModerately high
17Data valid but below normal range, least severeSlightly low
18Data valid but below normal range, moderately severeModerately low
19Received network data in errorBad data from another module
20Data drifted highSensor slowly reading higher than it should
21Data drifted lowSensor slowly reading lower than it should
31Condition existsA state is present, used by some makers for status faults

Cite or embed this

Notice the pattern: FMIs 0, 1 and 15 to 18 mean the reading is real but out of range, so look at the system itself. FMIs 3 to 6 mean an electrical circuit problem, so look at wiring and connectors first. FMI 2 and 19 often point to wiring, noise or another module.

Searchable index of SPN pages on this site

Type a code number or a part name to find our plain language page for it. This is not a complete database of every SPN; it lists the codes we have written up, and it grows as we add pages.

Pages for more codes are on the way, including SPN 2011 FMI 9, SPN 1231 FMI 9 for the second J1939 network and SPN 2659 FMI 0 for EGR flow. For a worked example of reading a code, see SPN 157 FMI 18, and for a network fault, SPN 639.

Reading three codes: a worked EXAMPLE

Say a scan tool shows three codes after a cold morning start. Here is how the FMI alone steers the first look, before any part is touched.

  • SPN 110 FMI 0, logged once. SPN 110 is engine coolant temperature, and FMI 0 means a real reading far above normal. Since it is real data, check the cooling system itself: coolant level, fan, thermostat and the radiator.
  • SPN 110 FMI 3, logged 14 times and inactive. Same sensor, but FMI 3 means the signal voltage was too high, a circuit problem. With a high count and no matching overheating, the sensor wiring or connector is the first suspect, not the cooling system.
  • SPN 639 FMI 14, logged by three modules. Several modules reporting a network fault at once points to shared wiring or low voltage during cranking, so check batteries and grounds before chasing any one module.

The same SPN with different FMIs can need completely different fixes, which is why you always read both numbers. Counts, active or inactive status and which module logged the code fill in the rest. This EXAMPLE shows the reasoning only; a technician should confirm with the maker's troubleshooting steps.

Standard vs proprietary SPNs

SPNs below 520192 are standard and defined in SAE J1939. The wording differs between makers, but the meaning is the same. SPNs from 520192 to 524287 are reserved for makers to define, so a proprietary code can mean one thing on a Cummins engine and something else on a PACCAR or Detroit engine. For those, only the maker's documents give the meaning.

Semi truck check engine light: what the lamps mean

Heavy trucks usually have several warning lamps tied to fault codes:

  • Amber check engine lamp: a fault was logged. Read the codes and get it checked soon.
  • Red stop engine lamp: a serious fault, such as low oil pressure or high coolant temperature. Stop safely as soon as you can. Some engines will shut down on their own after a warning.
  • Emissions lamp (MIL): an emissions-related fault, often with aftertreatment codes.
  • Aftertreatment lamps: DPF, high exhaust temperature and DEF lamps, each with their own codes.

A check engine light on a semi truck is never a code by itself. The code behind it tells you what happened.

How to read codes on your truck

  • Dash display. Many trucks list active codes in a diagnostics menu on the instrument cluster.
  • Handheld or laptop scan tool. It plugs into the 9-pin diagnostic connector, usually under the dash, and reads codes from every module, including inactive codes and counts.
  • Engine maker software. Dealers and many shops use the maker's own software, which gives full descriptions and troubleshooting steps.

Write down the SPN, FMI, count and module before clearing anything. Clearing codes without fixing the cause erases evidence a technician could use.

Common reasons for codes across many systems

  • Low battery voltage or poor grounds, which make many modules log faults at once. Check the truck battery and cables first when several unrelated codes appear.
  • Corroded or loose connectors, especially near the frame and engine.
  • Chafed wiring where it crosses frame rails.
  • Water in connectors after rain or washing.
  • Software issues that a maker update fixes.

Scanning for codes at every PM service catches problems before a lamp comes on. The preventive maintenance schedule generator can add a code scan to your plan.

Methodology and updates

The FMI meanings are written in our own words from the public descriptions of the SAE J1939 failure mode identifiers and checked against engine and transmission maker documents. SPN pages are added one at a time, each checked against at least one public maker or component document. This list is reviewed every quarter as new code pages are published. You are welcome to cite the FMI table with a credit link to this page.

Our semi truck warranty guide explains what factory, extended and third party plans usually cover.

Dispatch for 26 ft and up

TorqueLoads is a dispatch service for 26 ft box trucks and larger. We find and negotiate loads, the broker sends the rate confirmation to you, and you decide every load. Learn about our dispatch service, read about box truck dispatch, or apply.

SPN FMI codes list FAQs

What do SPN and FMI mean on a truck?
SPN stands for suspect parameter number and names what the fault is about, such as a pressure, a sensor or a network. FMI stands for failure mode identifier and says what kind of problem the computer sees, such as a value too high, a short circuit or a missing signal. Together they describe a fault on trucks that use the SAE J1939 standard.
What does the check engine light mean on a semi truck?
An amber check engine lamp means an engine or emissions fault was logged and should be checked soon. A red stop engine lamp means a serious fault that can damage the engine, and the driver should stop safely as soon as possible. Many trucks also have a separate emissions lamp. Read the codes to see what set the lamp.
How do I read fault codes on my semi truck?
Many trucks show active codes on the dash display through a diagnostics menu. A scan tool that plugs into the 9-pin diagnostic connector under the dash reads codes from every module, including inactive ones, and shows the SPN, FMI and occurrence count. Engine maker software gives the most detail and troubleshooting steps.
Are SPN codes the same for every truck maker?
Standard SPNs, defined in the SAE J1939 standard, mean the same thing on every truck that uses them, though makers word them differently. SPNs from 520192 to 524287 are reserved for makers to define for themselves, so the same number can mean different things on different engines. Always check proprietary codes against the maker's documents.

Apply for dispatch

Codes handled, loads covered

About 2 minutes. No setup fee. No contract. Every load is your call.

  • 26 ft cargo space minimum, 7 equipment types
  • No setup fee, no contract, no haul no pay
  • The rate confirmation comes to you and you sign it
STEP 1 OF 2 · WHAT DO YOU RUN?

BOX TRUCK · 26 FT MINIMUM

Prefer the full form? Use the long application.